Construction And Characteristics of Epoxy Polymer Membrane Electrode for Chloride

Hitoshi Ishiwada; Koji Suzuki; Tsuneo Shirai

doi:10.2116/bunsekikagaku.31.2_71

Construction And Characteristics of Epoxy Polymer Membrane Electrode for Chloride

Hitoshi Ishiwada, Koji Suzuki, Tsuneo Shirai

Department of Applied Chemistry

Research output: Contribution to journal › Article › peer-review

4 Citations (Scopus)

Abstract

Some different types of miniaturized polymer membrane electrodes (PMEs) for chloride ion were constructed by the use of epoxy matrix membrane. The PME of the best characteristics consists of a copper wire and three coating layers of silver paste of epoxy matrix type, silver chloride and epoxy matrix incorporating about 45 wt % of an ion exchanger solution. The most suitable ion exchanger solution was 1-decanol containing 0.4 wt % of trioctylmethylammonium chloride. The thickness of coating layers were (0.2~0.3) mm at each layer and the electrode was about 1 mm outer diameter. The responses of the PME were Nernstian for (5X10-5~4X 10-2) M chloride. The noise of the PME on electrode potential was ± 0.5 mV at the lower linear response range. The selectivity coefficients (K Yr) of the PME for perchlorate and iodide were 1.3 and 1.1, respectively.

Original language	English
Pages (from-to)	71-76
Number of pages	6
Journal	BUNSEKI KAGAKU
Volume	31
Issue number	2
DOIs	https://doi.org/10.2116/bunsekikagaku.31.2_71
Publication status	Published - 1982

Keywords

Ion-selective polymer membrane electrode for chloride ion

ASJC Scopus subject areas

Analytical Chemistry

Access to Document

10.2116/bunsekikagaku.31.2_71

Cite this

@article{8c183550356b421ab04743fbab44c498,

title = "Construction And Characteristics of Epoxy Polymer Membrane Electrode for Chloride",

abstract = "Some different types of miniaturized polymer membrane electrodes (PMEs) for chloride ion were constructed by the use of epoxy matrix membrane. The PME of the best characteristics consists of a copper wire and three coating layers of silver paste of epoxy matrix type, silver chloride and epoxy matrix incorporating about 45 wt % of an ion exchanger solution. The most suitable ion exchanger solution was 1-decanol containing 0.4 wt % of trioctylmethylammonium chloride. The thickness of coating layers were (0.2~0.3) mm at each layer and the electrode was about 1 mm outer diameter. The responses of the PME were Nernstian for (5X10-5~4X 10-2) M chloride. The noise of the PME on electrode potential was ± 0.5 mV at the lower linear response range. The selectivity coefficients (K Yr) of the PME for perchlorate and iodide were 1.3 and 1.1, respectively.",

keywords = "Ion-selective polymer membrane electrode for chloride ion",

author = "Hitoshi Ishiwada and Koji Suzuki and Tsuneo Shirai",

year = "1982",

doi = "10.2116/bunsekikagaku.31.2_71",

language = "English",

volume = "31",

pages = "71--76",

journal = "Bunseki Kagaku",

issn = "0525-1931",

publisher = "Japan Society for Analytical Chemistry",

number = "2",

}

TY - JOUR

T1 - Construction And Characteristics of Epoxy Polymer Membrane Electrode for Chloride

AU - Ishiwada, Hitoshi

AU - Suzuki, Koji

AU - Shirai, Tsuneo

PY - 1982

Y1 - 1982

N2 - Some different types of miniaturized polymer membrane electrodes (PMEs) for chloride ion were constructed by the use of epoxy matrix membrane. The PME of the best characteristics consists of a copper wire and three coating layers of silver paste of epoxy matrix type, silver chloride and epoxy matrix incorporating about 45 wt % of an ion exchanger solution. The most suitable ion exchanger solution was 1-decanol containing 0.4 wt % of trioctylmethylammonium chloride. The thickness of coating layers were (0.2~0.3) mm at each layer and the electrode was about 1 mm outer diameter. The responses of the PME were Nernstian for (5X10-5~4X 10-2) M chloride. The noise of the PME on electrode potential was ± 0.5 mV at the lower linear response range. The selectivity coefficients (K Yr) of the PME for perchlorate and iodide were 1.3 and 1.1, respectively.

AB - Some different types of miniaturized polymer membrane electrodes (PMEs) for chloride ion were constructed by the use of epoxy matrix membrane. The PME of the best characteristics consists of a copper wire and three coating layers of silver paste of epoxy matrix type, silver chloride and epoxy matrix incorporating about 45 wt % of an ion exchanger solution. The most suitable ion exchanger solution was 1-decanol containing 0.4 wt % of trioctylmethylammonium chloride. The thickness of coating layers were (0.2~0.3) mm at each layer and the electrode was about 1 mm outer diameter. The responses of the PME were Nernstian for (5X10-5~4X 10-2) M chloride. The noise of the PME on electrode potential was ± 0.5 mV at the lower linear response range. The selectivity coefficients (K Yr) of the PME for perchlorate and iodide were 1.3 and 1.1, respectively.

KW - Ion-selective polymer membrane electrode for chloride ion

UR - http://www.scopus.com/inward/record.url?scp=84996407685&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84996407685&partnerID=8YFLogxK

U2 - 10.2116/bunsekikagaku.31.2_71

DO - 10.2116/bunsekikagaku.31.2_71

M3 - Article

AN - SCOPUS:84996407685

VL - 31

SP - 71

EP - 76

JO - Bunseki Kagaku

JF - Bunseki Kagaku

SN - 0525-1931

IS - 2

ER -

Construction And Characteristics of Epoxy Polymer Membrane Electrode for Chloride

Abstract

Keywords

ASJC Scopus subject areas

Access to Document

Other files and links

Fingerprint

Cite this