Measurement of instantaneous heat flux flowing into metallic and ceramic combustion chamber walls

Atsushi Ishii, Hiroshi Nagano, Kazuaki Adachi, Shuji Kimura, Masao Koike, Norimasa Iida, Hiroyuki Ishii, Yoshiteru Enomoto

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Abstract

Accurate measurements of combustion gas temperature and the coefficient of heat transfer between the gas and the combustion chamber wall of internal combustion engine in cyclic operations are difficult at present. Hence the only method available for determination of states of thermal load and heat loss to the combustion chamber wall in a cycle is to measure the instantaneous temperature on the combustion chamber wall surface accurately and precisely using proper thin-film thermocouples, then to calculate the instantanenous heat flux flowing into the wall surface by means of numerical analysis. However, it is necessary to pay adequate attention to the effects of thermophysical properties of the thermocouple materials on the measured values, since any thermocouple consists of several kinds of materials which are different from those of portions to be measured. This paper describes findings obtained through the studies made on structures of thermocouples developed by the authors et al. aiming at accurate determinations of instantanenous heat flux flowing into metallic and ceramic combustion chamber walls, together with the results of the applications to actual engine operations.

Original languageEnglish
Title of host publicationSAE Technical Papers
DOIs
Publication statusPublished - 2000
EventInternational Spring Fuels and Lubricants Meeting and Exposition - Paris, France
Duration: 2000 Jun 192000 Jun 22

Other

OtherInternational Spring Fuels and Lubricants Meeting and Exposition
CountryFrance
CityParis
Period00/6/1900/6/22

Fingerprint

Combustion chambers
Thermocouples
Heat flux
Electric load loss
Thermal load
Internal combustion engines
Heat losses
Gases
Numerical analysis
Thermodynamic properties
Heat transfer
Engines
Thin films
Temperature

ASJC Scopus subject areas

  • Automotive Engineering
  • Safety, Risk, Reliability and Quality
  • Pollution
  • Industrial and Manufacturing Engineering

Cite this

Ishii, A., Nagano, H., Adachi, K., Kimura, S., Koike, M., Iida, N., ... Enomoto, Y. (2000). Measurement of instantaneous heat flux flowing into metallic and ceramic combustion chamber walls. In SAE Technical Papers https://doi.org/10.4271/2000-01-1815

Measurement of instantaneous heat flux flowing into metallic and ceramic combustion chamber walls. / Ishii, Atsushi; Nagano, Hiroshi; Adachi, Kazuaki; Kimura, Shuji; Koike, Masao; Iida, Norimasa; Ishii, Hiroyuki; Enomoto, Yoshiteru.

SAE Technical Papers. 2000.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Ishii, A, Nagano, H, Adachi, K, Kimura, S, Koike, M, Iida, N, Ishii, H & Enomoto, Y 2000, Measurement of instantaneous heat flux flowing into metallic and ceramic combustion chamber walls. in SAE Technical Papers. International Spring Fuels and Lubricants Meeting and Exposition, Paris, France, 00/6/19. https://doi.org/10.4271/2000-01-1815
Ishii A, Nagano H, Adachi K, Kimura S, Koike M, Iida N et al. Measurement of instantaneous heat flux flowing into metallic and ceramic combustion chamber walls. In SAE Technical Papers. 2000 https://doi.org/10.4271/2000-01-1815
Ishii, Atsushi ; Nagano, Hiroshi ; Adachi, Kazuaki ; Kimura, Shuji ; Koike, Masao ; Iida, Norimasa ; Ishii, Hiroyuki ; Enomoto, Yoshiteru. / Measurement of instantaneous heat flux flowing into metallic and ceramic combustion chamber walls. SAE Technical Papers. 2000.
@inproceedings{7891b46964dc47e3a8b2bc618d041d49,
title = "Measurement of instantaneous heat flux flowing into metallic and ceramic combustion chamber walls",
abstract = "Accurate measurements of combustion gas temperature and the coefficient of heat transfer between the gas and the combustion chamber wall of internal combustion engine in cyclic operations are difficult at present. Hence the only method available for determination of states of thermal load and heat loss to the combustion chamber wall in a cycle is to measure the instantaneous temperature on the combustion chamber wall surface accurately and precisely using proper thin-film thermocouples, then to calculate the instantanenous heat flux flowing into the wall surface by means of numerical analysis. However, it is necessary to pay adequate attention to the effects of thermophysical properties of the thermocouple materials on the measured values, since any thermocouple consists of several kinds of materials which are different from those of portions to be measured. This paper describes findings obtained through the studies made on structures of thermocouples developed by the authors et al. aiming at accurate determinations of instantanenous heat flux flowing into metallic and ceramic combustion chamber walls, together with the results of the applications to actual engine operations.",
author = "Atsushi Ishii and Hiroshi Nagano and Kazuaki Adachi and Shuji Kimura and Masao Koike and Norimasa Iida and Hiroyuki Ishii and Yoshiteru Enomoto",
year = "2000",
doi = "10.4271/2000-01-1815",
language = "English",
booktitle = "SAE Technical Papers",

}

TY - GEN

T1 - Measurement of instantaneous heat flux flowing into metallic and ceramic combustion chamber walls

AU - Ishii, Atsushi

AU - Nagano, Hiroshi

AU - Adachi, Kazuaki

AU - Kimura, Shuji

AU - Koike, Masao

AU - Iida, Norimasa

AU - Ishii, Hiroyuki

AU - Enomoto, Yoshiteru

PY - 2000

Y1 - 2000

N2 - Accurate measurements of combustion gas temperature and the coefficient of heat transfer between the gas and the combustion chamber wall of internal combustion engine in cyclic operations are difficult at present. Hence the only method available for determination of states of thermal load and heat loss to the combustion chamber wall in a cycle is to measure the instantaneous temperature on the combustion chamber wall surface accurately and precisely using proper thin-film thermocouples, then to calculate the instantanenous heat flux flowing into the wall surface by means of numerical analysis. However, it is necessary to pay adequate attention to the effects of thermophysical properties of the thermocouple materials on the measured values, since any thermocouple consists of several kinds of materials which are different from those of portions to be measured. This paper describes findings obtained through the studies made on structures of thermocouples developed by the authors et al. aiming at accurate determinations of instantanenous heat flux flowing into metallic and ceramic combustion chamber walls, together with the results of the applications to actual engine operations.

AB - Accurate measurements of combustion gas temperature and the coefficient of heat transfer between the gas and the combustion chamber wall of internal combustion engine in cyclic operations are difficult at present. Hence the only method available for determination of states of thermal load and heat loss to the combustion chamber wall in a cycle is to measure the instantaneous temperature on the combustion chamber wall surface accurately and precisely using proper thin-film thermocouples, then to calculate the instantanenous heat flux flowing into the wall surface by means of numerical analysis. However, it is necessary to pay adequate attention to the effects of thermophysical properties of the thermocouple materials on the measured values, since any thermocouple consists of several kinds of materials which are different from those of portions to be measured. This paper describes findings obtained through the studies made on structures of thermocouples developed by the authors et al. aiming at accurate determinations of instantanenous heat flux flowing into metallic and ceramic combustion chamber walls, together with the results of the applications to actual engine operations.

UR - http://www.scopus.com/inward/record.url?scp=84877189897&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84877189897&partnerID=8YFLogxK

U2 - 10.4271/2000-01-1815

DO - 10.4271/2000-01-1815

M3 - Conference contribution

BT - SAE Technical Papers

ER -