Haptic communication system using FPGA and real-time network framework

Hiroyuki Tanaka, Kouhei Ohnishi, Hiroaki Nishi

研究成果: Conference contribution

1 引用 (Scopus)

抄録

In this paper, a scheme for a haptic communication system is proposed by using an FPGA (Field Programmable Gate Array) and real-time network framework, RTnet. In the haptic communication system, the FPGA is used as a motion control processor, and the Linux-based real-time network framework is applied to the communication line between a master and a slave robot. The FPGA can execute control calculations in a short interval. Sending a large number of packets in a short period is, however, not acceptable for the communication line. In the haptic communication system, the FPGA execute the control calculation in every 50 μs, and the packets are sent in every 1 ms to prevent network congestion. The degrees-of-freedom(DOF) of the haptic device can be increased without increasing the number of sending packets, since the data of the each DOF is packed into one packet in a Linux module. In this paper, a master-slave haptic communication system is developed. The master side consists of a haptic device, whereas the slave side consists of a virtual haptic device and a virtual environment. The validity of the haptic communication system is shown through an experiment.

元の言語English
ホスト出版物のタイトルIECON Proceedings (Industrial Electronics Conference)
ページ2931-2936
ページ数6
DOI
出版物ステータスPublished - 2009
イベント35th Annual Conference of the IEEE Industrial Electronics Society, IECON 2009 - Porto, Portugal
継続期間: 2009 11 32009 11 5

Other

Other35th Annual Conference of the IEEE Industrial Electronics Society, IECON 2009
Portugal
Porto
期間09/11/309/11/5

Fingerprint

Field programmable gate arrays (FPGA)
Communication systems
Communication
Motion control
Virtual reality
Robots
Experiments
Linux

ASJC Scopus subject areas

  • Control and Systems Engineering
  • Electrical and Electronic Engineering

これを引用

Tanaka, H., Ohnishi, K., & Nishi, H. (2009). Haptic communication system using FPGA and real-time network framework. : IECON Proceedings (Industrial Electronics Conference) (pp. 2931-2936). [5415387] https://doi.org/10.1109/IECON.2009.5415387

Haptic communication system using FPGA and real-time network framework. / Tanaka, Hiroyuki; Ohnishi, Kouhei; Nishi, Hiroaki.

IECON Proceedings (Industrial Electronics Conference). 2009. p. 2931-2936 5415387.

研究成果: Conference contribution

Tanaka, H, Ohnishi, K & Nishi, H 2009, Haptic communication system using FPGA and real-time network framework. : IECON Proceedings (Industrial Electronics Conference)., 5415387, pp. 2931-2936, 35th Annual Conference of the IEEE Industrial Electronics Society, IECON 2009, Porto, Portugal, 09/11/3. https://doi.org/10.1109/IECON.2009.5415387
Tanaka H, Ohnishi K, Nishi H. Haptic communication system using FPGA and real-time network framework. : IECON Proceedings (Industrial Electronics Conference). 2009. p. 2931-2936. 5415387 https://doi.org/10.1109/IECON.2009.5415387
Tanaka, Hiroyuki ; Ohnishi, Kouhei ; Nishi, Hiroaki. / Haptic communication system using FPGA and real-time network framework. IECON Proceedings (Industrial Electronics Conference). 2009. pp. 2931-2936
@inproceedings{33f8bda5778742b7a4fc0eaf29b467b2,
title = "Haptic communication system using FPGA and real-time network framework",
abstract = "In this paper, a scheme for a haptic communication system is proposed by using an FPGA (Field Programmable Gate Array) and real-time network framework, RTnet. In the haptic communication system, the FPGA is used as a motion control processor, and the Linux-based real-time network framework is applied to the communication line between a master and a slave robot. The FPGA can execute control calculations in a short interval. Sending a large number of packets in a short period is, however, not acceptable for the communication line. In the haptic communication system, the FPGA execute the control calculation in every 50 μs, and the packets are sent in every 1 ms to prevent network congestion. The degrees-of-freedom(DOF) of the haptic device can be increased without increasing the number of sending packets, since the data of the each DOF is packed into one packet in a Linux module. In this paper, a master-slave haptic communication system is developed. The master side consists of a haptic device, whereas the slave side consists of a virtual haptic device and a virtual environment. The validity of the haptic communication system is shown through an experiment.",
author = "Hiroyuki Tanaka and Kouhei Ohnishi and Hiroaki Nishi",
year = "2009",
doi = "10.1109/IECON.2009.5415387",
language = "English",
pages = "2931--2936",
booktitle = "IECON Proceedings (Industrial Electronics Conference)",

}

TY - GEN

T1 - Haptic communication system using FPGA and real-time network framework

AU - Tanaka, Hiroyuki

AU - Ohnishi, Kouhei

AU - Nishi, Hiroaki

PY - 2009

Y1 - 2009

N2 - In this paper, a scheme for a haptic communication system is proposed by using an FPGA (Field Programmable Gate Array) and real-time network framework, RTnet. In the haptic communication system, the FPGA is used as a motion control processor, and the Linux-based real-time network framework is applied to the communication line between a master and a slave robot. The FPGA can execute control calculations in a short interval. Sending a large number of packets in a short period is, however, not acceptable for the communication line. In the haptic communication system, the FPGA execute the control calculation in every 50 μs, and the packets are sent in every 1 ms to prevent network congestion. The degrees-of-freedom(DOF) of the haptic device can be increased without increasing the number of sending packets, since the data of the each DOF is packed into one packet in a Linux module. In this paper, a master-slave haptic communication system is developed. The master side consists of a haptic device, whereas the slave side consists of a virtual haptic device and a virtual environment. The validity of the haptic communication system is shown through an experiment.

AB - In this paper, a scheme for a haptic communication system is proposed by using an FPGA (Field Programmable Gate Array) and real-time network framework, RTnet. In the haptic communication system, the FPGA is used as a motion control processor, and the Linux-based real-time network framework is applied to the communication line between a master and a slave robot. The FPGA can execute control calculations in a short interval. Sending a large number of packets in a short period is, however, not acceptable for the communication line. In the haptic communication system, the FPGA execute the control calculation in every 50 μs, and the packets are sent in every 1 ms to prevent network congestion. The degrees-of-freedom(DOF) of the haptic device can be increased without increasing the number of sending packets, since the data of the each DOF is packed into one packet in a Linux module. In this paper, a master-slave haptic communication system is developed. The master side consists of a haptic device, whereas the slave side consists of a virtual haptic device and a virtual environment. The validity of the haptic communication system is shown through an experiment.

UR - http://www.scopus.com/inward/record.url?scp=77951540302&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=77951540302&partnerID=8YFLogxK

U2 - 10.1109/IECON.2009.5415387

DO - 10.1109/IECON.2009.5415387

M3 - Conference contribution

AN - SCOPUS:77951540302

SP - 2931

EP - 2936

BT - IECON Proceedings (Industrial Electronics Conference)

ER -