Photo-induced surface modification of polyimides for printable electronics fabrication

T. Yamashita, F. Kodera, M. Mino, Y. Matsuzawa, K. Okano

研究成果: Conference contribution

抄録

Manufacturing flexible electronic devices with printing technique is one of the key steps, but printing fine structure with ink jet technique is relatively limited, because positional precision of ink droplet deposition and the size of an ink droplet are not smaller than several microns. We prepared those polyimides whose surface wetability can be changed by photoirradiation, with which surface wetability can be photo-lithographically patterned to make channels and an ink droplet spread along the patterned area with photolithographic resolution. The degree of surface contact angle change of water on the polyimide is as large as 70° between before and after the photoirradiation. The mechanism is confirmed as the chemically amplified reaction of t-BOC group, and photochemical reaction of benzophenone moiety. Surface relief structure can be also patterned only by exposure without development with those polyimides containing PAG or PBG as additives. The mechanism is determined as the difference in the imidization temperature. Positive or negative tone of the relief can be controlled by the selection of the additives. Porous structure pattering with turbid/transparent structure can be also patterned by photoirradiation. Those polyimides are potentially high performance and functional materials for printable and flexible electronic devices.

元の言語English
ホスト出版物のタイトルTechnical Proceedings of the 2012 NSTI Nanotechnology Conference and Expo, NSTI-Nanotech 2012
ページ291-294
ページ数4
出版物ステータスPublished - 2012
イベントNanotechnology 2012: Electronics, Devices, Fabrication, MEMS, Fluidics and Computational - 2012 NSTI Nanotechnology Conference and Expo, NSTI-Nanotech 2012 - Santa Clara, CA, United States
継続期間: 2012 6 182012 6 21

Other

OtherNanotechnology 2012: Electronics, Devices, Fabrication, MEMS, Fluidics and Computational - 2012 NSTI Nanotechnology Conference and Expo, NSTI-Nanotech 2012
United States
Santa Clara, CA
期間12/6/1812/6/21

Fingerprint

Ink
Polyimides
Surface treatment
Electronic equipment
Flexible electronics
Fabrication
Printing
Functional materials
Photochemical reactions
Contact angle
Water
Temperature

ASJC Scopus subject areas

  • Ceramics and Composites
  • Surfaces, Coatings and Films

これを引用

Yamashita, T., Kodera, F., Mino, M., Matsuzawa, Y., & Okano, K. (2012). Photo-induced surface modification of polyimides for printable electronics fabrication. : Technical Proceedings of the 2012 NSTI Nanotechnology Conference and Expo, NSTI-Nanotech 2012 (pp. 291-294)

Photo-induced surface modification of polyimides for printable electronics fabrication. / Yamashita, T.; Kodera, F.; Mino, M.; Matsuzawa, Y.; Okano, K.

Technical Proceedings of the 2012 NSTI Nanotechnology Conference and Expo, NSTI-Nanotech 2012. 2012. p. 291-294.

研究成果: Conference contribution

Yamashita, T, Kodera, F, Mino, M, Matsuzawa, Y & Okano, K 2012, Photo-induced surface modification of polyimides for printable electronics fabrication. : Technical Proceedings of the 2012 NSTI Nanotechnology Conference and Expo, NSTI-Nanotech 2012. pp. 291-294, Nanotechnology 2012: Electronics, Devices, Fabrication, MEMS, Fluidics and Computational - 2012 NSTI Nanotechnology Conference and Expo, NSTI-Nanotech 2012, Santa Clara, CA, United States, 12/6/18.
Yamashita T, Kodera F, Mino M, Matsuzawa Y, Okano K. Photo-induced surface modification of polyimides for printable electronics fabrication. : Technical Proceedings of the 2012 NSTI Nanotechnology Conference and Expo, NSTI-Nanotech 2012. 2012. p. 291-294
Yamashita, T. ; Kodera, F. ; Mino, M. ; Matsuzawa, Y. ; Okano, K. / Photo-induced surface modification of polyimides for printable electronics fabrication. Technical Proceedings of the 2012 NSTI Nanotechnology Conference and Expo, NSTI-Nanotech 2012. 2012. pp. 291-294
@inproceedings{44e8ac71da484673baa207799e93f896,
title = "Photo-induced surface modification of polyimides for printable electronics fabrication",
abstract = "Manufacturing flexible electronic devices with printing technique is one of the key steps, but printing fine structure with ink jet technique is relatively limited, because positional precision of ink droplet deposition and the size of an ink droplet are not smaller than several microns. We prepared those polyimides whose surface wetability can be changed by photoirradiation, with which surface wetability can be photo-lithographically patterned to make channels and an ink droplet spread along the patterned area with photolithographic resolution. The degree of surface contact angle change of water on the polyimide is as large as 70° between before and after the photoirradiation. The mechanism is confirmed as the chemically amplified reaction of t-BOC group, and photochemical reaction of benzophenone moiety. Surface relief structure can be also patterned only by exposure without development with those polyimides containing PAG or PBG as additives. The mechanism is determined as the difference in the imidization temperature. Positive or negative tone of the relief can be controlled by the selection of the additives. Porous structure pattering with turbid/transparent structure can be also patterned by photoirradiation. Those polyimides are potentially high performance and functional materials for printable and flexible electronic devices.",
keywords = "Patterning, Polyimide, Surface relief, Wetability",
author = "T. Yamashita and F. Kodera and M. Mino and Y. Matsuzawa and K. Okano",
year = "2012",
language = "English",
isbn = "9781466562752",
pages = "291--294",
booktitle = "Technical Proceedings of the 2012 NSTI Nanotechnology Conference and Expo, NSTI-Nanotech 2012",

}

TY - GEN

T1 - Photo-induced surface modification of polyimides for printable electronics fabrication

AU - Yamashita, T.

AU - Kodera, F.

AU - Mino, M.

AU - Matsuzawa, Y.

AU - Okano, K.

PY - 2012

Y1 - 2012

N2 - Manufacturing flexible electronic devices with printing technique is one of the key steps, but printing fine structure with ink jet technique is relatively limited, because positional precision of ink droplet deposition and the size of an ink droplet are not smaller than several microns. We prepared those polyimides whose surface wetability can be changed by photoirradiation, with which surface wetability can be photo-lithographically patterned to make channels and an ink droplet spread along the patterned area with photolithographic resolution. The degree of surface contact angle change of water on the polyimide is as large as 70° between before and after the photoirradiation. The mechanism is confirmed as the chemically amplified reaction of t-BOC group, and photochemical reaction of benzophenone moiety. Surface relief structure can be also patterned only by exposure without development with those polyimides containing PAG or PBG as additives. The mechanism is determined as the difference in the imidization temperature. Positive or negative tone of the relief can be controlled by the selection of the additives. Porous structure pattering with turbid/transparent structure can be also patterned by photoirradiation. Those polyimides are potentially high performance and functional materials for printable and flexible electronic devices.

AB - Manufacturing flexible electronic devices with printing technique is one of the key steps, but printing fine structure with ink jet technique is relatively limited, because positional precision of ink droplet deposition and the size of an ink droplet are not smaller than several microns. We prepared those polyimides whose surface wetability can be changed by photoirradiation, with which surface wetability can be photo-lithographically patterned to make channels and an ink droplet spread along the patterned area with photolithographic resolution. The degree of surface contact angle change of water on the polyimide is as large as 70° between before and after the photoirradiation. The mechanism is confirmed as the chemically amplified reaction of t-BOC group, and photochemical reaction of benzophenone moiety. Surface relief structure can be also patterned only by exposure without development with those polyimides containing PAG or PBG as additives. The mechanism is determined as the difference in the imidization temperature. Positive or negative tone of the relief can be controlled by the selection of the additives. Porous structure pattering with turbid/transparent structure can be also patterned by photoirradiation. Those polyimides are potentially high performance and functional materials for printable and flexible electronic devices.

KW - Patterning

KW - Polyimide

KW - Surface relief

KW - Wetability

UR - http://www.scopus.com/inward/record.url?scp=84864945616&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84864945616&partnerID=8YFLogxK

M3 - Conference contribution

AN - SCOPUS:84864945616

SN - 9781466562752

SP - 291

EP - 294

BT - Technical Proceedings of the 2012 NSTI Nanotechnology Conference and Expo, NSTI-Nanotech 2012

ER -